Adept technology 300CR Manuel d'utilisateur télécharger pdf (Page 75)

AdeptSix 300CR Robot Instruction Handbook, Rev. A 75

Using the Manual Control

Pendant (MCP) 8

8.1 MCP Usage for Six-Axis Robots

This section describes the coordinate system used by the AdeptSix 300CR robot. This

information is necessary when using the MCP to control the robot. See the Adept MV

Controller User’s Guide or the Adept SmartController User’s Guide for general details on

using and programming the MCP.

Joint Mode (Single-Axis Movement)

Joint motion is made around the axes of the various joints J1, J2, J3, etc. Use the + or -

speed bar key to specify rotational direction. See Figure 8-1 on page 76.

1 2 ... 70 71 72 73 74 75 76 77 78 79 80 ... 105 106

AdeptSix 300CR Robot 1
Table of Contents 5
List of Figures 9
List of Tables 11
Introduction 1 13
1.3 Checking Package Contents 14
Location 15
1.6 Related Manuals 16
1.5 How Can I Get Help? 16
1.7 Knowledge Express 17
Safety 2 19
Safety Barriers 20
Chapter 2 - Safety 22
2.3 Risk Assessment 23
Avoidance 24
2.5 Robot Modifications 26
2.7 Transport 27
2.9 Working Areas 28
Robot Installation 3 33
3.2 Transporting Method 34
Using the Forklift 36
3.3 Shipping Bracket and Jig 37
3.4 Installing Cover Bolts 37
3.5 Types of Mounting 38
3.7 Axis Naming Conventions 40
3.8 Grounding the Robot 41
M8 Bolt - for grounding 42
(provided at factory) 42
or more 42
4.1 System Cable Diagrams 43
Adept SmartController System 44
Connection to the Robot 45
MAI STATUS 47
DSP STATUS 47
Installing the MV Controller 48
SmartController 49
5.1 Allowable Wrist Load 51
5.2 Wrist Tool Flange 52
Example 1 54
Center of Gravity Position 55
= (100, 0, 70) 55
Total Weight 55
Approx. 6.3 [kg] 55
7.00 [kg] 55
* Unit of Length: [m] 56
* Unit of Ix, Iy, Iz: [kg.m 56
* Unit of Weight: [kg] 56
Example 2 57
Example 3 59
System Operation 63
MV Controller 6 63
6.5 Calibrate Robot 68
6.6 Turning Off the System 68
SmartController 7 69
7.5 Calibrate Robot 73
7.6 Turning Off the System 73
Using the Manual Control 75
Pendant (MCP) 8 75
Figure 8-1. Joint Mode 76
Moves in parallel with 77
Z-Axis 77
Coordinate System Definitions 78
Maintenance and Inspection 9 79
Operation 80
Connector Base (Top View) 84
Maintenance Procedures 85
Axis 6 speed reducer 90
Ti: Grease Inlet 90
G Nipple A-PT1/16 90
Notes for Maintenance 91
9.3 Spare Parts 93
Technical Specifications 10 95
10.4 Baseplate Dimensions 97
Point P working 98
Dimensions in mm 98
10.6 Axis 5 Working Range 99
-51˚ (Axis 3) 100
Numerics 101
01600-000, Rev. A 106

Commentaires sur ces manuels

Pas de commentaire

Adept technology 300CR Manuel d'utilisateur Page 75

Commentaires sur ces manuels